The ConoPoint-20 is the latest version in Optimet's family of point sensors. It's a non-contact optical sensor for distance and 3D measurements based on the unique conoscopic holography technology. The ConoPoint-20 measures the distance to a single point at a rate of up to 20,000 points/second with up to sub-micron precision.
The ConoPoint-20 offers a variety of objective lenses allowing various accuracies, resolutions, standoffs and measurement ranges in the same sensorThe ConoPoint-20 offers a variety of objective lenses allowing various accuracies, resolutions, standoffs and measurement ranges in the same sensor
All data processing is performed in the sensor head
The ConoPoint-20 supports external and internal trigger operation modes
Communication to PC is accomplished via standard Ethernet physical interface UDP protocol
Software integration is possible by using a single DLL file without any additional drivers or setups
Multiple sensors operation in parallel is possible using standard Ethernet switch/HUB
Measurement rate up to 20,000 Hz
Sub-micron precision with short focal length objectives
Analog output (optional)
Auto-exposure mode enabling measurement of high and low reflective surfaces in real time without changing laser power
Measurement of complex geometries, steep grooves, and angles up to ±85°
Integration capability with relay optics
The sensor can act as a Master synchronizer or as a Slave synchronized by a system
OPS (Optimet Position Synchronizer) capability which records encoders output and synchronizes the accurate position of up to three system axes together with the sensor’s measurements
Quality Control involves examining
the geometrical compliance or compatibility of a part with the original
design. In In-Process inspection the ConoPoint measures the parts in process,
and permits immediate correction of the process.
Turbine blade inspection:
Leading edge measurement Multiple sections of aerofoil blade profiles can be measured simultaneously on both sides and data compared with input design data. The Conopoint's ability to measure steep angles enables the system to address blade edge profiles. Single edge profiles can be measured or depending on blade twist 3D profiles of the full blade length can be produced.
Tire groove inspection
High speed inspection of deep tyre grooves is performed in seconds. The collinear technology and steep angle measurement capabilities provides the unique solution for a perfect defects profile comparison .
Filling level
In process inspection of liquid and solid (balls or powder) material height inside tubes is measured by comparing the distance between tube rim with the filling inside.
The precise position of the tube rim is calculated by measuring the radius of the rim by following its precise shape, then the distance to the powder/tiny balls is easy to measure due to the collinear properties of the Conopoint technology . This procedure has been adopted in hazardous and sterile environments at high speed movement.
Autofocus in welding applications
The autofocus assembly is a unique solution which permits to keep the welding laser in optimum focus by accurately position the focus lens exactly at the required clearance .It measures directly in the welding point during the welding, jointing or fusing process with a pulsed laser and readjust the focus lens immediately, when necessary. Because of the coaxial nature of the solution, it can measure inside grooves, holes and on steep slopes.
Reverse Engineering refers to the ability to reproduce the shape of an existing object.
Metal ornamentation and ceramics
Reliable and fast reconstruction of art industrial designs is accomplished using the Conopoint's unique capabilities to measure holes, grooves and steep angles on diffusive and shiny metal surfaces.
Jewelry
Accuracy and fidelity requirements of art related applications , such as coins, medals and jewels are met by precise replication of shapes, angles and small features provided by the Conopoint .
Leather
Reproduction of leather type surfaces is achieved by using high definition Conopoint sensors with extreme small size laser spot and high accuracy.
Lasts
Shoe last physical models created by crafts are reproduced with emphasis on complicated shapes of toes, and heels.
These parts are scanned with very steep angles over a large working range. This process is accomplished in a very short time due to the high precision measuring capabilities along the full size of the last and the collinear nature of the scanning technology avoiding blind areas around heels or toes.
Optimet offers a variety of objective
lenses, cables lengths and optical accessories enabling adaptation of its
sensors to a wide range of applications.
16mm
lens for standard ConoPoint
Microscope lens. High numeric aperture .High precision lens.
P/N 3Z83016
25mm
lens for standard ConoPoint
Popular for small feature scan in reverse engineering applications.
P/N 3Z83025
25mm Gold lens for standard ConoPoint
Distortion free aspheric lens.
P/N 3Z81030
40mm lens for standard ConoPoint
With standard sensor - for high precision and long standoff applications.
With HD sensor - for automotive QC engine applications.
P/N 3Z83040
50mm
lens for standard ConoPoint
Very popular in precise reverse engineering applications
P/N 3Z81050
75mm
lens for standard ConoPoint
Very popular in reverse engineering applications and in-process inspection
inside holes
P/N 3Z81075
100mm
lens for standard ConoPoint
Popular for wood industrial applications
P/N 3Z81100
150mm
for standard ConoPoint
Large working range
P/N 3Z82006
200mm for standard ConoPoint
Very large working range for large objects reconstruction as in shoe lasts.
P/N 3Z82007
250mm
for standard ConoPoint
Very large range coverage for free form objects
P/N 3Z82008
50mm
Extended Lens for standard ConoPoint
Best for small turbine blades
P/N 3Z83050E
75mm
Extended Lens for standard ConoPoint
High precision lens for long standoff measurement of turbine blades.
P/N 3Z83075E
125mm
Extended Lens for standard ConoPoint
For deep objects measurement - for avoiding collisions
P/N 3Z83125E
Above
250mm lens for the ConoPoint
Special for laser distance related applications.
For more details please contact our service center.
Custom
lenses
For more details please contact our service center.
CABLES
3
Meter D-TYPE cable P/N RH03061
5
Meter D-TYPE cable P/N RH03062
8
Meter D-TYPE cable P/N RH03063
12
Meter D-TYPE cable P/N RH03064
OPTICAL
ACCESSORIES
Periscope
The periscope is integrated with a regular 75mm lens and enables
measuring perpendicularly to the sensor's standard direction. P/N 3Z80510
ADDITIONAL
ACCESSORIES
PSRB
- calibration for measurement of semi-translucent materials
Enhanced operation mode enables the sensor to measure semi-transparent
materials (such as impression, wax and plastic materials) previously
impossible.
HUB
Multi sensor communication accessory box for one PC. P/N RD04034
The Setup includes a complete package of the files required to operate the sensor. The SDK provides code samples in addition to utilities that test the communication between the sensor and the PC.
Optimet LabVIEW SDK provides a simple and powerful interface to interact with any of OPTIMET’s point sensors in LabVIEW environment. LabVIEW SDK contains LabVIEW VIs file for API and sample application “Probe Tester” VI and compiled executable